Your Best Choice for AC Heat Pump and Furnace Repair in Indianapolis, IN (2)

No heat on Duncan gas furnace

I recently completed a job as a highly skilled HVAC contractor professional. The job involved inspecting and tuning up a Goodman 95% gas furnace. The furnace was installed in a residential home and had been experiencing issues with poor heating performance. During the inspection, I identified several areas that needed attention. The air filter was dirty and needed to be replaced, and the blower motor was not working properly. I also noticed that the furnace's combustion chamber was dirty, which could be causing the poor heating performance. To address these issues, I cleaned the air filter, replaced the blower motor, and cleaned the combustion chamber. I also adjusted the thermostat settings to ensure that the furnace was operating at the correct temperature. After completing the tune-up, the homeowner noticed a significant improvement in the heating performance of the furnace. The home was now warm and comfortable, and the homeowner was very satisfied with the work that I had done.

New HVAC install. Installed new Rheem gas furnace air conditioner.

Installed new condensate pump

I was called to a home to replace a bad transformer and high limit on a 4-year-old Goodman air conditioner. I arrived at the house and found the unit outside, and after a quick inspection, I determined that the transformer was faulty. I replaced the transformer and high limit, and the unit was up and running again in no time. The customer was very happy with the service, and I was able to provide them with a warranty for the work that I performed.

Performed seasonal safety inspection on grand Aire furnace

I was dispatched to a service call for a Goodman 4-year-old furnace with a bad high-limit switch. Upon arrival, I inspected the furnace and found that the high-limit switch had failed. I replaced the switch and tested the furnace to ensure it was operating correctly. I also provided the customer with information on how to maintain the furnace and prevent future issues.

I was called to a home to perform a tune-up and inspection on a Lennox gas furnace. The furnace was over 10 years old and had not been serviced in several years. I performed a thorough inspection of the furnace, including checking the burners, ignition, and safety controls. I also cleaned the furnace and replaced the air filter. After the tune-up, the furnace was running efficiently and the homeowner was happy with the results.

Cleaning on carrier furnace

No heat on ducane furnace in Indianapolis Indiana

Cleaning on heil furnace in Indianapolis Indiana

I recently completed a 95% gas furnace tune-up and inspection for a customer in the 11230 zip code area. The furnace was a Heil unit that was over 10 years old. During the tune-up, I performed a thorough inspection of the unit, including checking the burners, ignition system, blower motor, and other components. I also cleaned the unit's air filter and replaced the air filter if necessary. I also checked the thermostat and made any necessary adjustments to ensure that the furnace was operating at peak efficiency. Finally, I provided the customer with a detailed report of the tune-up and recommendations for any future maintenance or repairs. The customer was very satisfied with the work and expressed that the furnace was running much more efficiently now.

I was called to a home to perform a tune-up on a 2008 80% 2-stage furnace. The furnace was not producing heat and was blowing cold air. I checked the furnace and found that the blower motor was not working. I replaced the blower motor and the furnace was working again.

I was called to a home in the middle of a hot summer to replace a faulty air conditioner. Upon arrival, I found that the system was not cooling the home effectively. I diagnosed the problem as a faulty compressor and replaced the part. After completing the repair, I tested the system to ensure it was running properly. The homeowner was very satisfied with the work and expressed gratitude for the quick and efficient service.

"I was dispatched to a residential property to investigate a blown transformer due to a power surge. Upon arrival, I found that the transformer had been damaged and was no longer functional. I worked with the homeowner to determine the best course of action, which included replacing the transformer and restoring power to the property. It was a challenging job, but I was able to complete it successfully.

I recently completed a Heil heat pump tune-up and inspection for a client in the area. The Heil heat pump is a popular choice for residential and commercial applications, and it was important to ensure that it was operating efficiently and effectively. During the tune-up, I performed a thorough inspection of the unit, including checking the refrigerant levels, electrical connections, and airflow. I also cleaned the coils and inspected the blower motor and fan blades for any signs of wear or damage. After the inspection, I provided the client with a detailed report outlining the findings and recommending any necessary repairs or maintenance. I also offered to schedule a follow-up appointment to ensure that the unit continues to operate smoothly throughout the heating season. Overall, the Heil heat pump tune-up and inspection was a successful and efficient process that helped the client maintain the efficiency and reliability of their heating system.

I was called to a home to perform a Rheem furnace tune-up and humidifier pad replacement. Upon arrival, I found that the furnace was not producing heat and the humidifier was not working. I inspected the furnace and found that the blower motor was not working properly, causing the furnace to not produce heat. I replaced the blower motor and the humidifier pad, and the furnace was back up and running properly. The customer was very happy with the service and thanked me for my help.

New HVAC install. Installed new Rheem 95% gas furnace.

Cleaning on two rheem gas furnaces and serviced humidifier in Carmel Indiana

I am a highly skilled and experienced home service professional. I recently completed a job for a client who needed a Trane heat pump tune-up and inspection. The heat pump was over 10 years old and had been experiencing some issues with efficiency and performance. During the tune-up, I thoroughly inspected the unit, including the compressor, evaporator coil, condenser coil, and electrical components. I cleaned the coils, checked the refrigerant levels, and tested the electrical connections. I also performed a leak test to ensure that there were no leaks in the system. After the tune-up, I provided the client with a detailed report outlining the findings and recommendations for any necessary repairs or maintenance. The client was very pleased with the results and expressed satisfaction with my work. Overall, the job was a success, and the client was happy with the results. I am proud of the work that I do and take great pride in providing my clients with high-quality service and work

I am an HVAC contractor technician, and I recently completed a job that involved repairing a Rheem furnace's flame sensor. The furnace was not producing heat, and the customer suspected that the flame sensor was the issue. To diagnose the problem, I first checked the power supply to the furnace and found that it was working correctly. Then, I removed the flame sensor from the furnace and tested it with a multimeter to ensure that it was receiving power. I found that the flame sensor was not working, so I replaced it with a new one. After replacing the flame sensor, the furnace started producing heat again, and the customer was happy with the results. I also provided the customer with some tips on how to maintain the furnace to prevent future problems. Overall, the job was successful, and the customer

I recently completed a Goodman furnace tune-up and inspection at a residential property. The furnace was over 10 years old and had been experiencing some issues with efficiency and heating. During the tune-up, I performed a thorough inspection of the unit, including checking the burners, ignition system, and safety controls. I also cleaned the burners, inspected the heat exchanger, and replaced the air filter. After the tune-up, the furnace was running more efficiently and heating the home more effectively. The homeowner was very pleased with the results and expressed satisfaction with the service.

Cleaning on rheem high efficiency gas furnace in Carmel Indiana

I was called to a home in the middle of a heat wave to repair a 2013 Ducane 92% gas furnace. The customer reported that the furnace was not producing heat, and I arrived to find the inducer motor had failed. I replaced the inducer motor and tested the furnace, and it was working properly. The customer was happy with the service and paid me for the repair.

I recently completed a tune-up on a 2021 80% Goodman gas furnace. The furnace was installed in a residential home and had been experiencing issues with poor heating performance. During the tune-up, I performed a thorough inspection of the furnace, including checking the electrical connections, gas pressure, and combustion efficiency. I also cleaned and adjusted the burners, inspected the heat exchanger, and replaced any worn or damaged parts. After the tune-up, the furnace was running smoothly and efficiently, providing the homeowner with warm and comfortable heating throughout the winter.

I recently completed a repair/tune up on a 2017 Ducane 80% gas furnace. The furnace was not producing heat properly and was blowing cold air. I diagnosed the issue as a faulty igniter and replaced it. After replacing the igniter, the furnace was able to produce heat again. I also performed a safety check on the furnace and made sure all the connections were tight and secure.

I was hired to replace the inducer motor on a 2020 92% furnace. The motor was located in a tight space, and I had to remove several components to access it. I replaced the old motor with a new one and made sure it was properly installed and connected. I also tested the motor to ensure it was working correctly.

I recently completed a job as an HVAC contractor where I installed a new Rheem furnace and performed a tune-up and inspection. The furnace was installed in a residential home and was a high-efficiency model with a variable-speed blower and a programmable thermostat. During the tune-up, I checked the electrical connections, inspected the blower motor and heat exchanger, and adjusted the burner assembly. I also cleaned the air filter and inspected the ductwork for any leaks or damage. The inspection revealed that the furnace was operating efficiently and that there were no issues with the system. The homeowner was pleased with the work and expressed satisfaction with the new furnace.

I recently completed a tune-up on a newly installed Rheem 80% gas furnace. The furnace was installed in a residential home and had been operating for several months without any issues. However, the homeowner noticed that the furnace was not performing as efficiently as it should be and was experiencing some issues with temperature regulation. During the tune-up, I thoroughly inspected the furnace and identified several areas that needed attention. I cleaned the burners, inspected the gas pressure, and adjusted the thermostat. I also checked the air filter and replaced it if necessary. After completing the tune-up, the furnace was running more efficiently and the homeowner noticed a significant improvement in temperature regulation. They were also happy to know that their furnace was operating safely and reliably. Overall, the tune-up was a successful and cost-effective way to ensure that the furnace was operating at its peak performance. The homeowner was very satisfied with the res

I was called to a home to perform a tune-up on a Goodman furnace. The furnace was not working properly, and the customer was experiencing issues with the heat. I arrived at the home and performed a thorough inspection of the furnace. I found that the furnace had a dirty air filter, which was causing the furnace to work harder than it should. I cleaned the air filter and replaced the furnace's blower motor. After completing the tune-up, the furnace was working properly again. The customer was very happy with the service and thanked me for my help.

I was called to a home to perform a Rheem gas furnace tune-up. The furnace was not heating properly, and the customer was concerned that it might need to be replaced. I arrived at the house and performed a thorough inspection of the furnace. I checked the gas pressure, the ignition system, and the airflow. I also cleaned the burners and inspected the heat exchanger for any signs of damage. After the tune-up, the furnace was heating properly, and the customer was happy with the results. I provided the customer with a maintenance contract for the furnace and answered any questions they had about maintaining their heating system.

I recently completed an annual tune-up and inspection on a 2022 Bryant 95% gas furnace. The furnace was installed in a residential home and had been operating without any issues. During the tune-up, I checked the electrical connections, inspected the burners, inspected the blower, and tested the thermostat. I also cleaned the furnace and replaced the air filter. The customer was very satisfied with the service and expressed that the furnace was running more efficiently than ever before.

I was called to a home to perform a tune-up on a Payne 95% gas furnace. The furnace had been running poorly and was not heating the home adequately. I inspected the furnace and found that the burners were dirty and needed to be cleaned. I also replaced the air filter and checked the gas pressure. After completing the tune-up, the furnace was running smoothly and heating the home effectively. The homeowner was very pleased with the results and thanked me for my service.

I was called to a home to perform a tune-up on a newer Trane gas furnace. The homeowner had noticed that the furnace was not heating the home as efficiently as it should be. I arrived at the house and performed a thorough inspection of the furnace. I checked the electrical connections, the gas pressure, and the airflow. I also cleaned the burners and inspected the blower motor. After completing the inspection, I made the necessary adjustments and repairs to the furnace. The homeowner was very pleased with the results and thanked me for my help.

I recently completed a furnace annual tune-up and inspection for a customer in Grand Aire. The furnace was over 10 years old and had not been serviced in several years. During the tune-up, I cleaned the burners, inspected the blower, checked the thermostat, and tested the safety controls. I also replaced the air filter and lubricated the motor. The customer was very pleased with the results and said that the furnace was running much more efficiently now.

I am a skilled professional that works for a A Perfect Climate Heating & Cooling company. I recently completed an annual tune-up and inspection on a Trane furnace. The furnace was over 15 years old and had not been serviced in several years. During the inspection, I checked the electrical connections, inspected the burners, inspected the blower, and checked the heat exchanger for cracks. I also cleaned the furnace and replaced the air filter. The customer was very happy with the service and said that the furnace was running much more efficiently now.

I am a highly skilled and experienced home service professional. I recently completed an annual tune-up on a Rheem variable speed gas furnace. The furnace was installed in a residential home and had not been serviced in several years. During the tune-up, I checked the electrical connections, inspected the burners, inspected the blower motor and inspected the heat exchanger. I also cleaned the air filter and checked the thermostat settings. After the tune-up, the furnace was running smoothly and efficiently. The homeowner was very pleased with the results and expressed that they would recommend my services to others. I am proud of the work that I do and take great pride in providing my customers with high-quality service. I am always willing to go the extra mile to ensure that my customers are satisfied with my work.

New HVAC install. Installed new Rheem gas furnace.

I was called to a home to perform a tune-up on a Rheem gas furnace. The furnace had been running poorly for a while, and the homeowner was concerned about the cost of repairs. I arrived at the house and performed a thorough inspection of the furnace. I checked the electrical connections, the gas pressure, and the airflow. I also cleaned the burners and inspected the heat exchanger for any signs of damage. After the tune-up, the furnace was running like new. The homeowner was happy with the results and thanked me for my service.

I was hired to install a new Gree heat pump in a home. The job was to remove the old unit, install the new unit, and test the system to ensure it was working properly. I also inspected the unit to ensure it was installed correctly and met all safety standards.

I was hired to perform a tune-up on a carrier air handler and inspection. The air handler was not operating correctly, and the inspection revealed that the unit needed to be replaced. I replaced the unit with a new one and performed a thorough inspection of the system to ensure it was operating correctly.

I recently completed a furnace tune-up and inspection at a residential home. The furnace was over 10 years old and had not been serviced in several years. During the tune-up, I cleaned the burners, inspected the gas pressure, and adjusted the thermostat. I also checked the blower motor and inspected the electrical connections. After the tune-up, I provided the homeowner with a detailed report of my findings and recommendations for any necessary repairs or maintenance.

I was called to repair a Concord 80% gas furnace. The furnace was not heating the house, so I checked the thermostat, and it was set to 60 degrees. I checked the gas valve and found that it was open. I checked the pilot light and found that it was out. I replaced the pilot light and the furnace started working again. I also checked the blower and found that it was not working properly. I replaced the blower and the furnace started working again. I also checked the thermostat and found that it was set to 70 degrees. I reset the thermostat and the furnace started working again.

I was called to inspect a variable speed gas tube on a heating and air conditioning unit. The unit was not working properly, and the technician suspected that the tube was the issue. After inspecting the tube, he determined that it was not the problem. He then checked the electrical connections and found that one of the wires was loose. He tightened the wire and the unit started working again. The technician also cleaned the unit's air filter and checked the refrigerant levels. He found that the refrigerant levels were low, so he added more refrigerant and tested the unit again. The unit was now working properly.

I was hired to perform an annual time up and inspection on a Heil heat pump. The heat pump was installed in a residential home and had been operating for several years. The inspection was conducted to ensure that the heat pump was operating properly and to identify any potential issues that could affect its performance. During the inspection, I checked the electrical connections, inspected the compressor, checked the refrigerant levels, and tested the fan motor. I also checked the air filter and cleaned it if necessary. If any issues were found during the inspection, I provided a detailed report to the homeowner outlining the findings and recommending any necessary repairs or maintenance. I also provided a quote for the repairs or maintenance if the homeowner decided to proceed. Overall, the annual time up and inspection was a successful process that helped ensure that the heat pump was operating properly and that the homeowner was aware of any potential issues that could affect its